Introduction to Key Fob Battery Replacement
Replacing the battery in your Hyundai Tucson key fob is a straightforward process that can save you time and money. This guide will walk you through each step to ensure a smooth and successful battery replacement. The key fob in question is used for Hyundai Tucson models from 2014 to 2019 and requires a CR2032 battery.
- Plastic, Metal
- Imported
- IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032
Tools and Materials Needed
Before you begin, gather the necessary tools and materials. You will need a flathead screwdriver and a CR2032 battery. These items are inexpensive and can be easily purchased online.
- Flathead screwdriver
- CR2032 battery
If you don’t have these items, you can find them on Amazon.
- Plastic, Metal
- Imported
- IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032
- Cost savings
- Convenience
- Quick process
- If the key fob doesn’t work after replacing the battery, ensure the battery is correctly positioned.
- Check for any loose components inside the key fob.
- Make sure the new battery is not defective.
- Plastic, Metal
- Imported
- IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032
Step-by-Step Battery Replacement
Now that you have your tools and materials ready, follow these steps to replace the battery in your Hyundai Tucson key fob.
Step 1: Remove the Internal Key
First, press the button on the bottom of the key fob to remove the internal key. This will reveal a hole where the key was located and a slot next to it.
Step 2: Open the Key Fob
Insert your flathead screwdriver into the slot next to the hole and twist it to open the key fob. Position the screwdriver until it locks in place, then twist with some force to separate the two halves of the key fob.
Once the halves are separated, you can use your fingers to fully open the key fob and set it aside.
Step 3: Remove the Old Battery
Inside the key fob, you will see the battery housed in a plastic casing. It’s difficult to remove the battery with your fingers, so use a small precision screwdriver to pry it out. Insert the tool into the small opening in the plastic, wiggle and pry until the battery pops out.
Step 4: Insert the New Battery
Take a new CR2032 battery and ensure the positive side with the battery information faces down. Position it into the housing by pushing it down first into the metal component before clicking the top into place. Apply pressure to the center of the battery to secure it.
Step 5: Reassemble the Key Fob
Ensure that the circuit board and any rubber components are correctly positioned. Gently place the battery on top and click everything back together. If the battery has juice and everything is correctly assembled, the light on the key fob will come on.
Finally, reinsert the internal key into the key fob, and you’re done!
Benefits of Replacing Your Own Key Fob Battery
Replacing your own key fob battery has several advantages:
By doing it yourself, you avoid the hassle and expense of visiting a dealership or locksmith. The entire process takes just a few minutes and requires minimal effort.
Common Issues and Troubleshooting
While replacing the battery is usually straightforward, you may encounter some common issues. Here are a few troubleshooting tips:
If you follow these steps and still encounter issues, consider consulting the full guide on the Hyundai Tucson key fob replacement.
Frequently Asked Questions (FAQ)
What type of battery does the Hyundai Tucson key fob use?
The Hyundai Tucson key fob uses a CR2032 battery.
Where can I buy a CR2032 battery?
You can purchase a CR2032 battery online from retailers like Amazon.
Do I need any special tools to replace the battery?
A flathead screwdriver and a small precision screwdriver are recommended. These tools make it easier to open the key fob and remove the old battery.
How often should I replace the key fob battery?
Key fob batteries typically last 1-2 years. Replace the battery when you notice a decrease in range or if the key fob stops working.
Can I use a different type of battery?
It’s best to use the recommended CR2032 battery for optimal performance and compatibility.
What should I do if the key fob still doesn’t work after replacing the battery?
Double-check the battery’s position and ensure all components are secure. If issues persist, the new battery may be defective or there may be an issue with the key fob itself.
Conclusion
Replacing the battery in your Hyundai Tucson key fob is a quick and easy task that can be done at home. By following this guide, you can ensure your key fob remains functional and reliable. For more detailed information, visit the full guide on keyfobreplacement.com. Thank you for reading, and happy driving!