Introduction
Replacing the battery in your Chevrolet Trax key fob is easier than you might think. You don’t need to take it to the dealership. With just a few simple tools, you can do it yourself in under five minutes.
- Plastic, Metal
- Imported
- IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032
Tools and Materials Needed
The tools required for this task are minimal. You will need:
- Flathead screwdriver
- CR2032 battery
If you don’t have a CR2032 battery on hand, you can easily purchase one from Amazon.com.
Understanding Your Key Fob
The Chevrolet Trax key fob comes in two versions: a three-button and a four-button model. Regardless of which one you have, the process to replace the battery is the same.
Step-by-Step Battery Replacement
The battery replacement process is straightforward. Follow these steps:
Removing the Internal Key
First, locate the button on the left side of your key fob. Press and hold this button to release the internal key. Pull out the key and set it aside; you’ll need it shortly.
Prying Open the Key Fob
Insert the key into the keyhole and use it to pry off the back section of the plastic casing. Be careful not to insert it too far; a slight insertion will suffice. Apply upward pressure while prying to open the seam in the plastic. Once you’ve found the sweet spot, the back will pop open easily.
Accessing and Removing the Old Battery
With the back cover removed, you’ll see the battery. If you have short nails, use a flathead screwdriver, pen, or another small tool to lift the battery out. Dispose of the old battery properly.
Inserting the New Battery
Take your new CR2032 battery and ensure the positive side (indicated by a plus sign) is facing down. Place it into the slot and press it down until it sits flat.
Reassembling the Key Fob
Align the back section of the plastic casing with the key fob. Make sure the button aligns correctly to avoid damaging the fob. Press the back cover until it clicks into place. Finally, reinsert the internal key.
- Plastic, Metal
- Imported
- IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032
Final Thoughts
Congrats! You’ve successfully replaced the battery in your Chevrolet Trax key fob. This simple task can save you time and money.
If you found this guide helpful, consider checking out more tutorials on our website. We cover a wide range of models and makes, ensuring you have the information you need for any key fob battery replacement.
FAQs
What type of battery does the Chevrolet Trax key fob use?
The Chevrolet Trax key fob uses a CR2032 battery.
Can I use a different type of battery?
It’s recommended to use a CR2032 battery to ensure compatibility and proper functionality.
Is the process the same for both the three-button and four-button key fobs?
Yes, the process is identical for both versions of the key fob.
Do I need any special tools?
No, just a flathead screwdriver and the new CR2032 battery.
Can I damage the key fob by prying it open?
If done carefully, prying open the key fob should not cause any damage. Ensure you do not insert the key too far into the keyhole.
How often should I replace the key fob battery?
Typically, a key fob battery lasts between 1-2 years, but it can vary based on usage.
What should I do if the key fob still doesn’t work after replacing the battery?
Ensure the battery is inserted correctly with the positive side facing down. If the problem persists, the key fob might have other issues that need professional attention.
Where can I buy a CR2032 battery?
You can purchase a CR2032 battery from Amazon or any local electronics store.
- Plastic, Metal
- Imported
- IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032
For more detailed guides on other Chevrolet models, check out our Chevrolet Key Fobs Guide.