Introduction
Replacing the battery in your Mitsubishi Outlander key fob is a straightforward process. With just a few tools and a CR1620 battery, you can do it yourself at home. This guide will walk you through each step of the process.
- LONG LASTING PERFORMANCE: Panasonic CR1620 3.V batteries are engineered to provide reliable, long-lasting power
- CHILD RESISTANT SAFETY STANDARDS BASED PACKAGING: These authentic Panasonic lithium battery cells and packaging (in our “sunburst” package as shown) meet or exceed IEC 60086-4:2019; ANSI C18.3M Part 2:2024; CFR 16, Part 1700.20 and CFR 16, Part 1263 as required by Reese’s Law (Pub. L. 117-171, 15 U.S.C 2056e)
- LONG STORAGE LIFE: Our CR1620 batteries maintain power up to 8 years when unused and properly stored
Tools and Materials Needed
To replace the battery in your Mitsubishi Outlander key fob, you will need the following tools and materials:
- CR1620 battery
- Flathead screwdriver
- Small Phillips head screwdriver
If you don’t have these tools, you can purchase a set of precision screwdrivers online. They are affordable and highly recommended for this task.
Step-by-Step Guide to Replacing the Battery
Follow these steps to replace the battery in your Mitsubishi Outlander key fob:
1. Remove the Screw
Start by locating the small screw on the back of the key fob. Use a small Phillips head screwdriver to remove the screw. Set the screw aside in a safe place.
2. Open the Key Fob
Next, look for a slot along the seam at the bottom of the key fob. Insert a flathead screwdriver into the slot and gently twist until the two halves of the key fob come apart.
3. Remove the Old Battery
Once the key fob is open, you will see the battery. There is a small opening in the corner of the battery compartment. Use a precision screwdriver, needle, pin, or toothpick to pry the battery out. Gently push down and pry the battery up.
4. Insert the New Battery
Take your new CR1620 battery and ensure the positive side is facing up. Slide the battery towards the two plastic tabs that hold it in place, then push it down on the opposite side to snap it into position.
5. Reassemble the Key Fob
Line up the two halves of the key fob and squeeze them together. Replace the screw and twist it back in with your Phillips head screwdriver.
6. Test the Key Fob
To verify that you have replaced the battery correctly, press one of the buttons on the key fob. If the light comes on, you have successfully replaced the battery.
- LONG LASTING PERFORMANCE: Panasonic CR1620 3.V batteries are engineered to provide reliable, long-lasting power
- CHILD RESISTANT SAFETY STANDARDS BASED PACKAGING: These authentic Panasonic lithium battery cells and packaging (in our “sunburst” package as shown) meet or exceed IEC 60086-4:2019; ANSI C18.3M Part 2:2024; CFR 16, Part 1700.20 and CFR 16, Part 1263 as required by Reese’s Law (Pub. L. 117-171, 15 U.S.C 2056e)
- LONG STORAGE LIFE: Our CR1620 batteries maintain power up to 8 years when unused and properly stored
Frequently Asked Questions
What type of battery does the Mitsubishi Outlander key fob use?
The Mitsubishi Outlander key fob uses a CR1620 coin battery.
Do I need any special tools to replace the battery?
No, you only need a flathead screwdriver and a small Phillips head screwdriver. A precision screwdriver set can be helpful but is not necessary.
How do I know if I installed the battery correctly?
After replacing the battery, press one of the buttons on the key fob. If the light comes on, the battery is installed correctly.
Can I use a different type of battery?
No, it is important to use a CR1620 battery as this is the correct type specified for the Mitsubishi Outlander key fob.
Where can I purchase a CR1620 battery?
You can purchase a CR1620 battery from various online retailers such as Amazon. They are also available at most electronics and hardware stores.
- LONG LASTING PERFORMANCE: Panasonic CR1620 3.V batteries are engineered to provide reliable, long-lasting power
- CHILD RESISTANT SAFETY STANDARDS BASED PACKAGING: These authentic Panasonic lithium battery cells and packaging (in our “sunburst” package as shown) meet or exceed IEC 60086-4:2019; ANSI C18.3M Part 2:2024; CFR 16, Part 1700.20 and CFR 16, Part 1263 as required by Reese’s Law (Pub. L. 117-171, 15 U.S.C 2056e)
- LONG STORAGE LIFE: Our CR1620 batteries maintain power up to 8 years when unused and properly stored
What should I do if the key fob still doesn’t work after replacing the battery?
If the key fob doesn’t work after replacing the battery, double-check to ensure the battery is installed correctly with the positive side facing up. If it still doesn’t work, the key fob may have another issue that requires professional assistance.
Conclusion
Replacing the battery in your Mitsubishi Outlander key fob is a simple task that you can do at home with minimal tools. By following this guide, you can save time and money by avoiding a trip to the dealership. If you found this guide helpful, feel free to leave feedback or explore other tutorials on our website, FobBattery.com, for more key fob battery replacement guides.