Introduction to Key Fob Battery Replacement
Replacing the battery in your Dodge Charger key fob is a straightforward process. This guide will walk you through the steps needed to replace the battery in key fobs for 2006 and 2007 models. With just a few tools and a new battery, you can have your key fob working like new in no time.
- Plastic, Metal
- Imported
- IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032
Tools and Materials Needed
Before you begin, make sure you have the necessary tools and materials. You’ll need:
- CR2032 coin battery
- Flathead screwdriver
You can easily purchase a CR2032 coin battery from various online retailers..
Step-by-Step Instructions
Follow these steps to replace the battery in your Dodge Charger key fob:
1. Locate the Slot
First, locate the small slot on the seam between the two halves of the key fob. This is where you’ll insert your flathead screwdriver.
2. Insert the Screwdriver
Carefully insert the flathead screwdriver into the slot. Gently twist the screwdriver until you hear a click. This indicates that the two halves of the key fob have started to separate.
3. Open the Key Fob
Once you hear the click, continue to twist the screwdriver gently. You should now be able to pull the key fob apart with your fingers. Set the top half of the key fob aside.
4. Remove the Rubber Component
Inside the key fob, you’ll find a rubber component covering the circuit board. Carefully remove this rubber piece and set it aside as well.
5. Remove the Old Battery
The battery is now exposed. Using your flathead screwdriver, gently lift the battery from underneath it. The battery should pop out easily.
6. Insert the New Battery
Take your new CR2032 battery and place it face down, with the positive side facing down. Click it into place securely.
7. Reassemble the Key Fob
Place the rubber component back over the circuit board. Then, click the two halves of the key fob back together until they snap into place.
Conclusion
And that’s it! You’ve successfully replaced the battery in your Dodge Charger key fob. If you found this guide helpful, feel free to leave a comment or check out more of our resources on key fob maintenance.
- Plastic, Metal
- Imported
- IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032
Frequently Asked Questions (FAQ)
What type of battery does the Dodge Charger key fob use?
The Dodge Charger key fob for 2006 and 2007 models uses a CR2032 coin battery.
Where can I buy a CR2032 battery?
You can purchase a CR2032 battery from various online retailers, Amazon.
- Plastic, Metal
- Imported
- IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032
Do I need any special tools to replace the battery?
No, you only need a flathead screwdriver to open the key fob and replace the battery.
How often should I replace the key fob battery?
Typically, you should replace the key fob battery every 1-2 years, or when you notice a decrease in range or responsiveness.
Can I replace the battery myself?
Yes, replacing the battery is a simple process that you can do yourself at home with minimal tools.
What should I do if my key fob still doesn’t work after replacing the battery?
If your key fob doesn’t work after replacing the battery, ensure the new battery is properly installed. If it still doesn’t work, there may be an issue with the key fob itself or the vehicle’s receiver.
Is it safe to use a different type of battery?
No, always use the specified CR2032 battery to ensure proper functionality and avoid damaging the key fob.
Can I use rechargeable batteries?
It’s not recommended to use rechargeable batteries in key fobs as they may not provide the consistent voltage required for proper operation.