Introduction
In this guide, I will show you how to replace the battery in your Chevrolet Captiva Sport key fob. This task is straightforward and will take you less than five minutes to complete. You only need a flathead screwdriver and a CR2032 battery, which you can purchase online for a few dollars.
- Plastic, Metal
- Imported
- IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032
Tools and Materials Needed
- Flathead screwdriver
- CR2032 battery
Step-by-Step Instructions
Identify the Key Fob Type
First, it’s important to note that there are different versions of this key fob. Some may have three buttons, while others have four. Regardless of the layout, the procedure for replacing the battery is the same.
Locate the Indentation
Look at the bottom of the device along the seam in the plastic. You will see a small indentation or a thin slot. This is where you will insert your flathead screwdriver to open the key fob.
Insert and Twist the Screwdriver
Insert the flathead screwdriver into the indentation. Push and wiggle it until it gets stuck. Once it’s securely in place, give it a little twist to start opening the key fob.
Open the Key Fob
Once you feel the key fob start to open, stop twisting. Use your fingers to pull it apart. If it’s still tight, twist the screwdriver again to open it without damaging the plastic.
Remove the Circuit Board
After opening the key fob, the circuit board will likely come out. This is expected and perfectly fine. Set the two pieces of plastic aside and focus on the battery.
Remove the Old Battery
Slide the old CR2032 battery out of its place. This should be very easy to do. Dispose of the old battery properly.
Insert the New Battery
Take your new CR2032 battery. Ensure the positive side, marked with a plus sign, is facing up. Slide it into the same place where the old battery was.
Reassemble the Key Fob
Drop the circuit board back into its rubber housing with the battery facing up. Then, take the back section of plastic and set it on top. Squeeze the pieces together until they snap back into place.
- Plastic, Metal
- Imported
- IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032
Conclusion
And that’s it! You’ve successfully replaced the battery in your Chevrolet Captiva Sport key fob. This simple process can save you time and money. If you found this guide helpful, feel free to let me know in the comments or by liking this post. If you need help with other key fobs, visit our website at FobBattery.com for more tutorials.
FAQ
Can I use a different type of battery?
No, you should use a CR2032 battery as specified. Other batteries may not fit or work correctly.
What if my key fob still doesn’t work after replacing the battery?
Check to make sure the battery is installed correctly with the positive side facing up. If it still doesn’t work, the issue may be with the circuit board.
Is it safe to open the key fob myself?
Yes, as long as you follow these instructions carefully, it’s safe to open the key fob and replace the battery.
How often should I replace the key fob battery?
Typically, a key fob battery lasts about 1-2 years. If the range of your key fob decreases or it stops working, it’s time to replace the battery.
Where can I dispose of the old battery?
Used batteries should be disposed of at a battery recycling center or a designated collection point. Do not throw them in the trash.
Can I use a different tool instead of a flathead screwdriver?
A flathead screwdriver is recommended, but any similar tool that fits into the indentation can work.
Will this process void my warranty?
Replacing the battery yourself typically does not void the warranty. However, it’s always best to check your warranty terms.
Can I get the battery from a physical store?
Yes, CR2032 batteries are widely available in electronics stores, supermarkets, and pharmacies.
- Plastic, Metal
- Imported
- IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032