Jeep Patriot Key Fob Battery Replacement Guide (2007 – 2017)

Introduction to Key Fob Battery Replacement

Changing the battery in your Jeep Patriot key fob is a straightforward process. This guide will walk you through each step to ensure you can replace the battery quickly and efficiently. The key fob for the Jeep Patriot from 2007 to 2017 uses a CR2032 coin battery, which is readily available online.

In this guide, I’ll show you how to replace your key fob battery at home. You don’t need any special tools, just a flathead screwdriver and a new CR2032 battery.

Amazon Basics 4-Pack CR2032 Lithium Coin Cell Battery, Compatible with AirTag, 3 Volt, Long Lasting Power, Mercury-Free
  • Plastic, Metal
  • Imported
  • IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032

Materials Needed

  • CR2032 coin battery
  • Flathead screwdriver

You can purchase the CR2032 battery online. I’ve included a link for convenience, where you can buy it on Amazon for just a few dollars.

Step-by-Step Instructions

Step 1: Open the Key Fob

First, locate the small slot on your key fob. This slot is designed to help you open the key fob. Insert a flathead screwdriver into this slot.

Gently twist the screwdriver until the two halves of the key fob start to separate. Be careful not to apply too much force, as this could damage the key fob.

Once you have a small gap, you can pull the two halves apart. If necessary, you can continue twisting the screwdriver along the opening to fully separate the halves.

Step 2: Remove the Old Battery

With the key fob open, you’ll see a rubber component covering the circuit board. Carefully remove this rubber piece and set it aside.

Underneath the rubber component, you’ll find the old CR2032 battery. Use your flathead screwdriver to gently lift the battery out of its compartment.

Step 3: Insert the New Battery

Take your new CR2032 battery and ensure the positive side is facing down. Place the battery into the compartment and press it down until it clicks into place.

Step 4: Reassemble the Key Fob

Now that the new battery is in place, it’s time to reassemble the key fob. Start by placing the rubber component back over the circuit board.

Align the two halves of the key fob and press them together until they click back into place.

Congratulations, you’ve successfully replaced the battery in your Jeep Patriot key fob!

Amazon Basics 4-Pack CR2032 Lithium Coin Cell Battery, Compatible with AirTag, 3 Volt, Long Lasting Power, Mercury-Free
  • Plastic, Metal
  • Imported
  • IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032

Tips for Battery Replacement

  • Work on a clean, flat surface
  • Use gentle pressure when opening the key fob
  • Double-check the battery orientation

Why Replace Your Key Fob Battery?

Replacing your key fob battery is essential for maintaining the functionality of your vehicle’s remote system. A weak or dead battery can prevent you from locking or unlocking your car remotely. It can also lead to a range of other issues, such as reduced range or intermittent operation.

By replacing the battery yourself, you save time and money. There’s no need to visit a dealership or hire a professional for this simple task.

Frequently Asked Questions (FAQ)

How often should I replace the key fob battery?

The key fob battery typically lasts between 1 to 2 years. If you notice a decrease in range or response time, it’s time to replace the battery.

Can I use a different type of battery?

No, you should only use a CR2032 battery for the Jeep Patriot key fob. Using a different type of battery can damage the key fob.

What should I do if the key fob doesn’t work after replacing the battery?

First, double-check that the battery is installed correctly. Ensure the positive side is facing down. If the key fob still doesn’t work, the problem may be with the key fob itself, not the battery.

Do I need any special tools to replace the battery?

No, you only need a flathead screwdriver to open the key fob. No other special tools are required.

Where can I buy a CR2032 battery?

You can purchase CR2032 batteries online or at most electronic stores. I’ve included a link to buy it on Amazon for your convenience.

Amazon Basics 4-Pack CR2032 Lithium Coin Cell Battery, Compatible with AirTag, 3 Volt, Long Lasting Power, Mercury-Free
  • Plastic, Metal
  • Imported
  • IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032

Conclusion

Replacing the battery in your Jeep Patriot key fob is a simple task that you can do at home. With just a flathead screwdriver and a new CR2032 battery, you can ensure your key fob remains functional.

By following the steps outlined in this guide, you’ll have your key fob working like new in no time. If you found this guide helpful, feel free to leave a comment or like. For more information on changing batteries in key fobs of nearly every make and model, check out fobbattery.com. Thank you for reading!

Proudly powered by WordPress | Theme: Sprout Blog by Crimson Themes.