Introduction
Replacing the battery in your Mitsubishi Lancer key fob is a straightforward task. With the right tools and a few minutes, you can get your key fob working like new. This guide will walk you through the process step by step.
- LONG LASTING PERFORMANCE: Panasonic CR1620 3.V batteries are engineered to provide reliable, long-lasting power
- CHILD RESISTANT SAFETY STANDARDS BASED PACKAGING: These Panasonic CR1620 batteries and packaging meet or exceed IEC 60086-4, ANSI c18-3m part 2, and UL 1642 compliance standards
- LONG STORAGE LIFE: Our CR1620 batteries maintain power up to 8 years when unused and properly stored
Tools and Materials Needed
Before starting, gather the necessary tools and materials:
- CR1620 battery
- Small screwdrivers
- Precision screwdriver or pin
The CR1620 battery is the only type that will fit this key fob. You can find it easily on Amazon or at local stores.
Step 1: Remove the Screw
Start by locating the small Phillips head screw on the back of the key fob. Use a small Phillips head screwdriver to twist out the screw. Set the screw aside safely.
It’s important to use the right size screwdriver to avoid damaging the screw head. If you don’t have one, consider purchasing a small screwdriver set.
Step 2: Open the Key Fob
Next, identify the slot near the top of the key fob. Insert a flathead screwdriver or a precision tool into the slot. Gently twist to open the key fob.
Be careful not to apply too much force, as this could damage the plastic casing.
Step 3: Remove the Old Battery
Inside the key fob, the battery is held securely in place. Locate the small hole in the top corner of the battery compartment. Use a precision screwdriver, pin, or needle to gently pry the battery out.
The battery should come out with minimal force. Dispose of the old battery properly.
Step 4: Insert the New Battery
Take your new CR1620 battery and ensure the positive side is facing up. Slide the battery under the two plastic tabs on one side of the compartment. Then, press down to secure the battery in place.
Make sure the battery is seated correctly to ensure proper functionality.
Step 5: Reassemble the Key Fob
Align the two halves of the key fob and snap them back together. Ensure all edges are flush and there are no gaps.
Reinsert the small screw and twist it back in using the Phillips head screwdriver. Tighten the screw securely, but do not over-tighten.
Step 6: Test the Key Fob
Press any button on the key fob to verify that the battery replacement was successful. The light should turn on, indicating the key fob is working properly.
If the light does not turn on, double-check the battery orientation and ensure it is seated correctly.
- LONG LASTING PERFORMANCE: Panasonic CR1620 3.V batteries are engineered to provide reliable, long-lasting power
- CHILD RESISTANT SAFETY STANDARDS BASED PACKAGING: These Panasonic CR1620 batteries and packaging meet or exceed IEC 60086-4, ANSI c18-3m part 2, and UL 1642 compliance standards
- LONG STORAGE LIFE: Our CR1620 batteries maintain power up to 8 years when unused and properly stored
FAQ
Can I use a different type of battery?
No, you should only use a CR1620 battery for the Mitsubishi Lancer key fob. Other batteries may not fit or function correctly.
What if I don’t have a precision screwdriver?
You can use a pin or needle to pry the battery out. However, a precision screwdriver is recommended for ease and safety.
Where can I buy the CR1620 battery?
You can purchase the CR1620 battery on Amazon or at most electronics stores. It’s a common battery used in various devices.
- LONG LASTING PERFORMANCE: Panasonic CR1620 3.V batteries are engineered to provide reliable, long-lasting power
- CHILD RESISTANT SAFETY STANDARDS BASED PACKAGING: These Panasonic CR1620 batteries and packaging meet or exceed IEC 60086-4, ANSI c18-3m part 2, and UL 1642 compliance standards
- LONG STORAGE LIFE: Our CR1620 batteries maintain power up to 8 years when unused and properly stored
How often should I replace the key fob battery?
Typically, the key fob battery lasts about 2-3 years. If your key fob starts to have a weak signal or stops working, it’s time to replace the battery.
Can I damage the key fob during the battery replacement?
If you follow the steps carefully and use the right tools, the risk of damaging the key fob is minimal. Avoid using excessive force when prying the fob open.
Conclusion
Replacing the battery in your Mitsubishi Lancer key fob is a simple process that can save you time and money. By following this guide, you can ensure your key fob continues to work reliably.
For more guides on key fob battery replacements, visit FobBattery.com. We provide detailed instructions for a wide range of vehicles.