Introduction to Key Fob Battery Replacement
Replacing the battery in your Subaru Tribeca key fob is a straightforward process. This guide will walk you through each step, ensuring your key fob is back in working order quickly. You will need a CR1620 battery, a flathead screwdriver, and a Phillips head screwdriver.
- LONG LASTING PERFORMANCE: Panasonic CR1620 3.V batteries are engineered to provide reliable, long-lasting power
- CHILD RESISTANT SAFETY STANDARDS BASED PACKAGING: These authentic Panasonic lithium battery cells and packaging (in our “sunburst” package as shown) meet or exceed IEC 60086-4:2019; ANSI C18.3M Part 2:2024; CFR 16, Part 1700.20 and CFR 16, Part 1263 as required by Reese’s Law (Pub. L. 117-171, 15 U.S.C 2056e)
- LONG STORAGE LIFE: Our CR1620 batteries maintain power up to 8 years when unused and properly stored
Gathering Your Tools and Materials
Before starting the replacement process, gather the necessary tools and materials. You will need:
- CR1620 battery
- Flathead screwdriver
- Phillips head screwdriver
Make sure your screwdrivers are the correct size to avoid stripping the screws. Precision screwdrivers are recommended for this task.
Step-by-Step Battery Replacement
Follow these steps to replace the battery in your Subaru Tribeca key fob:
Step 1: Remove the Screw
First, use your Phillips head screwdriver to remove the small screw on the back of the key fob. Be careful not to lose the screw once it is removed.
Step 2: Separate the Key Fob
After removing the screw, you can pull the back piece of plastic off. If it is stuck, use a flathead screwdriver to gently pry it apart. Insert the flathead screwdriver between the plastic and the key and wiggle it to loosen the back piece.
Step 3: Remove the Inner Component
Inside the key fob, you will find a small box containing the buttons and the battery. Carefully lift this inner component out. You can turn the key fob over and push the buttons out if that is easier.
Step 4: Open the Battery Compartment
Using the flathead screwdriver, push under the small flap of plastic at the bottom of the inner component to open the battery compartment. Be cautious to avoid dislodging the rubber component or circuit board, as this keeps the buttons in place.
Step 5: Remove the Old Battery
With the battery compartment open, use the flathead screwdriver to lift the old CR1620 battery out. Note the orientation of the battery before removal.
Step 6: Insert the New Battery
Take your new CR1620 battery and insert it into the compartment, ensuring the positive side (marked with text and battery information) is facing down. Click the battery into place securely.
Step 7: Reassemble the Key Fob
Reassemble the key fob by placing the inner component back into the key fob casing. Ensure the buttons are correctly aligned and not falling out. Attach the back piece of plastic by hooking it onto the latch and then clicking the bottom into place.
Step 8: Secure the Screw
Finally, reinsert the screw and tighten it to finger tightness. Avoid over-tightening to prevent stripping the screw.
- LONG LASTING PERFORMANCE: Panasonic CR1620 3.V batteries are engineered to provide reliable, long-lasting power
- CHILD RESISTANT SAFETY STANDARDS BASED PACKAGING: These authentic Panasonic lithium battery cells and packaging (in our “sunburst” package as shown) meet or exceed IEC 60086-4:2019; ANSI C18.3M Part 2:2024; CFR 16, Part 1700.20 and CFR 16, Part 1263 as required by Reese’s Law (Pub. L. 117-171, 15 U.S.C 2056e)
- LONG STORAGE LIFE: Our CR1620 batteries maintain power up to 8 years when unused and properly stored
Conclusion
The battery replacement process for your Subaru Tribeca key fob is simple and can be completed in a few minutes. Following these steps will ensure your key fob is functional again. For additional guidance on other key fob models, visit our website or check out our other videos.
FAQ
What type of battery does the Subaru Tribeca key fob use?
The Subaru Tribeca key fob uses a CR1620 coin battery.
What tools do I need to replace the key fob battery?
You will need a flathead screwdriver and a Phillips head screwdriver. Precision screwdrivers are recommended.
How do I avoid losing the small screw?
Place the screw in a small container or on a magnetic surface to keep it secure during the replacement process.
What should I do if the buttons fall out?
Carefully reassemble the buttons in their correct positions. Be cautious when opening the battery compartment to prevent this from happening.
Can I use a different type of battery?
No, it is important to use a CR1620 battery to ensure compatibility and proper function of the key fob.
How do I know if the battery is installed correctly?
The positive side of the battery should be facing down. Ensure it clicks securely into place.
What if my key fob still doesn’t work after replacing the battery?
Double-check the battery orientation and ensure all components are properly reassembled. If issues persist, consult a professional for further assistance.
Where can I buy a CR1620 battery?
You can purchase a CR1620 battery online from retailers like Amazon.
- LONG LASTING PERFORMANCE: Panasonic CR1620 3.V batteries are engineered to provide reliable, long-lasting power
- CHILD RESISTANT SAFETY STANDARDS BASED PACKAGING: These authentic Panasonic lithium battery cells and packaging (in our “sunburst” package as shown) meet or exceed IEC 60086-4:2019; ANSI C18.3M Part 2:2024; CFR 16, Part 1700.20 and CFR 16, Part 1263 as required by Reese’s Law (Pub. L. 117-171, 15 U.S.C 2056e)
- LONG STORAGE LIFE: Our CR1620 batteries maintain power up to 8 years when unused and properly stored