How to Replace the Battery in Your Toyota Land Cruiser Key Fob (2018-2021)

Introduction

Replacing the battery in your Toyota Land Cruiser key fob is a simple process that you can do at home. This guide will walk you through each step, ensuring that your key fob functions seamlessly. All you need is a CR2032 coin battery and a flathead screwdriver.

Amazon Basics 4-Pack CR2032 Lithium Coin Cell Battery, Compatible with AirTag, 3 Volt, Long Lasting Power, Mercury-Free
  • Plastic, Metal
  • Imported
  • IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032

Gather Your Tools

Before you begin, make sure you have the necessary tools:

  • CR2032 coin battery
  • Flathead screwdriver

You can purchase the CR2032 battery online. I recommend getting it from Amazon for a few bucks. A link to the battery is provided in the description.

Step 1: Remove the Internal Key

First, flip the key fob over. You’ll notice a small switch. Hold down this switch while pulling out the internal key.

Once the key is out, you will see a large hole and a smaller slot beside it. This slot is where you will insert the flathead screwdriver.

Step 2: Open the Key Fob

Insert the flathead screwdriver into the slot beside the keyhole. Twist the screwdriver gently while holding the key fob loosely. This action will help you pry apart the two halves of the key fob.

Once you have a gap, use your fingers to pull the two halves apart carefully.

Step 3: Remove the Circuit Board

Inside the key fob, you’ll find a circuit board. Carefully remove this circuit board to reveal the battery underneath.

Step 4: Extract the Old Battery

Now, take your flathead screwdriver and insert it between the battery and the black plastic behind it. Hold the key fob by the sides and apply constant pressure with the screwdriver.

Wiggle the screwdriver to get under the battery and pry it out. You can also twist the screwdriver if needed. Once the battery is loose, pull it out with your fingers.

Step 5: Insert the New Battery

Take your new CR2032 battery. Ensure the positive side is facing up. Place the battery into the slot where the old battery was located.

Make sure the battery is securely in place before proceeding to the next step.

Step 6: Reassemble the Key Fob

Place the circuit board back into its original position. Align the two halves of the key fob and press them together until you hear a click.

Finally, insert the internal key back into its slot. Your key fob is now ready to use!

Amazon Basics 4-Pack CR2032 Lithium Coin Cell Battery, Compatible with AirTag, 3 Volt, Long Lasting Power, Mercury-Free
  • Plastic, Metal
  • Imported
  • IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032

Conclusion

Replacing the battery in your Toyota Land Cruiser key fob is a straightforward process. With a CR2032 battery and a flathead screwdriver, you can complete the task in just a few minutes.

If you found this guide helpful, feel free to leave a comment. For more key fob tutorials, visit our YouTube channel or our website at fobbattery.com.

FAQ

What type of battery do I need?

You need a CR2032 coin battery for your Toyota Land Cruiser key fob.

Where can I buy the CR2032 battery?

You can purchase the CR2032 battery online from Amazon. It’s also available at most electronic stores.

Amazon Basics 4-Pack CR2032 Lithium Coin Cell Battery, Compatible with AirTag, 3 Volt, Long Lasting Power, Mercury-Free
  • Plastic, Metal
  • Imported
  • IN THE BOX: 4-pack of CR2032 3 volt lithium coin cell batteries; replacement for BR2032, DL2032, and ECR2032

Do I need any special tools?

No, you only need a flathead screwdriver to open the key fob and replace the battery.

How often should I replace the battery?

The battery typically lasts 1-2 years. If your key fob starts to lose range or stops working, it’s time to replace the battery.

Can I use a different type of battery?

No, it’s important to use a CR2032 battery as it is specifically designed for the key fob.

What if my key fob still doesn’t work?

If your key fob doesn’t work after replacing the battery, you may need to contact a professional for further assistance.

Is this process the same for other Toyota models?

This process is similar for many Toyota models, but always refer to your vehicle’s manual for specific instructions.

Can I damage my key fob by replacing the battery?

If you follow the steps carefully, you should not damage your key fob. Handle all components gently.

Proudly powered by WordPress | Theme: Sprout Blog by Crimson Themes.